Altera Embedded Peripherals IP Uživatelský manuál Strana 67
- Strana / 336
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Bit(s) Name Access Description
[32:16
]
RAVAIL R The number of characters remaining in the read FIFO (after
the current read).
A read from the data register returns the first character from the FIFO (if one is available) in the DATA
field. Reading also returns information about the number of characters remaining in the FIFO in the
RAVAIL field. A write to the data register stores the value of the DATA field in the write FIFO. If the write
FIFO is full, the character is lost.
Control Register
Embedded software controls the JTAG UART core's interrupt generation and reads status information via
the control register. The Control Register Bits table below describes the function of each bit.
Table 7-6: Control Register Bits
Bit(s) Name Access Description
0 RE R/W Interrupt-enable bit for read interrupts.
1 WE R/W Interrupt-enable bit for write interrupts.
8 RI R Indicates that the read interrupt is pending.
9 WI R Indicates that the write interrupt is pending.
10 AC R/C Indicates that there has been JTAG activity since the
bit was cleared. Writing 1 to AC clears it to 0.
[32:16] WSPACE R The number of spaces available in the write FIFO.
A read from the control register returns the status of the read and write FIFOs. Writes to the register can
be used to enable/disable interrupts, or clear the AC bit.
The RE and WE bits enable interrupts for the read and write FIFOs, respectively. The WI and RI bits
indicate the status of the interrupt sources, qualified by the values of the interrupt enable bits (WE and RE).
Embedded software can examine RI and WI to determine the condition that generated the IRQ. See the
Interrupt Behavior section for further details.
The AC bit indicates that an application on the host PC has polled the JTAG UART core via the JTAG
interface. Once set, the AC bit remains set until it is explicitly cleared via the Avalon interface. Writing 1 to
AC clears it. Embedded software can examine the AC bit to determine if a connection exists to a host PC. If
no connection exists, the software may choose to ignore the JTAG data stream. When the host PC has no
data to transfer, it can choose to poll the JTAG UART core as infrequently as once per second. Delays
caused by other host software using the JTAG download cable could cause delays of up to 10 seconds
between polls.
Interrupt Behavior
The JTAG UART core generates an interrupt when either of the individual interrupt conditions is
pending and enabled.
Interrupt behavior is of interest to device driver programmers concerned with the bandwidth perform‐
ance to the host PC. Example designs and the JTAG terminal program provided with Nios II Embedded
Design Suite (EDS) are pre-configured with optimal interrupt behavior.
7-10
Control Register
UG-01085
2014.24.07
Altera Corporation
JTAG UART Core
Send Feedback
- 101 Innovation Drive 1
- San Jose, CA 95134 1
- Contents 2
- Altera Corporation 10
- Introduction 14
- Device Support 15
- December 16
- Initial release. — 16
- SDRAM Controller Core 17
- Avalon-MM Interface 18
- Off-Chip SDRAM Interface 18
- Memory Profile Page 21
- Timing Page 22
- SDRAM Memory Model 23
- Symptoms of an Untuned PLL 26
- Example Calculation 27
- Parameter Symbol 28
- Value (ns) in -7 Speed Grade 28
- Min. Max 28
- Parameter Symbol Value (ns) 28
- Tri-State SDRAM 31
- Configuration Parameter 32
- Interface 33
- Reset and Clock Requirements 38
- Architecture 38
- Block Level Usage Model 39
- Compact Flash Core 41
- Required Connections 42
- (32-bit Word Address) 54
- Register Name R/W 54
- Bit Description 54
- JTAG UART Core 58
- Read and Write FIFOs 59
- JTAG Interface 59
- Host-Target Connection 59
- Simulation Settings 61
- UART Core 70
- RS-232 Interface 71
- Transmitter Logic 71
- Instantiating the Core 72
- Data Bits, Stop Bits, Parity 73
- Synchronizer Stages 74
- Flow Control 74
- Streaming Data (DMA) Control 74
- Request Description 79
- Bit Name Access Description 81
- May 2008 86
- 16550 UART 87
- Unsupported Features 88
- General Architecture 90
- Configuration Parameters 90
- DMA Support 91
- FPGA Resource Usage 91
- Timing and Fmax 92
- Avalon-MM Slave 93
- Overrun/Underrun Conditions 94
- Hardware Auto Flow-Control 95
- 16550 UART API 98
- Private APIs 99
- UART Device Structure 100
- Figure 9-7: 101
- Driver Examples 102
- UG-01085 103
- 2014.24.07 103
- Document Revision History 106
- SPI Core 107
- txdata 108
- Receiver Logic 109
- Master and Slave Modes 109
- Slave Mode Operation 110
- Multi-Slave Environments 110
- Configuration 111
- Data Register Settings 112
- Timing Settings 112
- Software Programming Model 113
- Software Files 114
- Register Map 115
- # Name Description 116
- Date and 118
- Document 118
- Core Overview 119
- Functional Description 119
- Interrupt Behavior 121
- PIO Core 123
- Data Input and Output 124
- Edge Capture 124
- IRQ Generation 124
- Example Configurations 125
- Input Options 126
- Operation 132
- PCI Lite Core 135
- Avalon-MM Ports 137
- Prefetchable Avalon-MM Master 137
- I/O Avalon-MM Master 138
- PCI Bus Access Slave 138
- Master and Target Performance 139
- Space Indicator 141
- (Bits 1:0) 141
- Description 141
- Avalon-to-PCI Write Request 142
- Ordering of Requests 143
- Send Feedback 145
- PCI Timing Constraint Files 146
- Simulation Considerations 147
- Simulation Flow 149
- MDIO Core 151
- MDIO Frame Format (Clause 45) 152
- MDIO Clock Generation 153
- Interfaces 153
- Parameter 154
- Configuration Registers 154
- On-Chip FIFO Memory Core 156
- Offset Bits Field Description 158
- FIFO Settings 161
- Interface Parameters 161
- Software Control 163
- Field Type Description 164
- Bit(s) Name Description 164
- Software Example 166
- On-Chip FIFO Memory API 167
- Multi-Channel Shared FIFO 176
- Parameters 177
- Address Width 178
- Name Access Reset 180
- Bytes Converter Cores 185
- Feature Property 186
- Transaction 190
- DMA Descriptors 197
- Error Conditions 198
- Signal Type Description 199
- Timeouts 206
- Data Structure 207
- SG-DMA API 208
- Name Description 209
- Overview 217
- Feature Description 217
- Component Interface 220
- Descriptor Slave Port 221
- Component GUI 222
- Byte Lanes 223
- Read and Write Address Fields 224
- Length Field 224
- Sequence Number Field 225
- Read and Write Stride Fields 225
- Control Field 225
- Bit Sub-Field Name Definition 226
- Register Map of mSGDMA 228
- Status Register 229
- Control Register 229
- Bit Name Description 230
- Offset Access 3 2 1 0 230
- Unsupported Feature 231
- DMA Controller Core 232
- Setting Up DMA Transactions 233
- Advanced Options 235
- Video Sync Generator 242
- Parameter Name Description 244
- Horizontal sync pulse 245
- Horizontal front porch 245
- Horizontal blank pixels 245
- Pixel Converter 246
- Interval Timer Core 249
- Counter Size 251
- Hardware Options 251
- Bit Name R/W/C Description 255
- Mutex Core 258
- Mutex API 260
- Mailbox Core 264
- Mailbox API 267
- Functional Blocks 273
- Register Maps 275
- Run-time Initialization 285
- Board Support Package 285
- VIC IRQ RRS RIL 291
- November 293
- Altera FPGA 294
- Core Behavior 295
- System ID Core 298
- Performance Counter Core 301
- Global Counter 302
- Using the Performance Counter 304
- Name (1) Meaning 305
- Performance Counter API 306
- PERF_START_MEASURING() 307
- PERF_STOP_MEASURING() 307
- PERF_BEGIN() 307
- PERF_END() 308
- PLL Cores 312
- Registers 313
- PLL Core 313
- ALTPLL Megafunction 313
- Instantiating the PLL Core 314
- Altera MSI to GIC Generator 320
- Interrupt Servicing Process 321
- Registers of Component 322
- Altera SMBus Core Interface 324
- Component Parameterization 326
- Frequency Register 331
- 32-bit Counter 332
- Software Access 334
- Implementation Details 335
- IP Caveats 336
Související produkty a manuály pro Měřící nástroje Altera Embedded Peripherals IP
Měřící nástroje Altera JESD204B IP Uživatelský manuál
(158 stránky)
(158 stránky)
Měřící nástroje Altera Nios II Embedded Evaluation Kit Cyclone III Editio Uživatelský manuál
(3 stránky)
(3 stránky)
Měřící nástroje Altera Nios II Embedded Evaluation Kit Cyclone III Editio Uživatelský manuál
(80 stránky)
(80 stránky)
Měřící nástroje Altera SCFIFO Uživatelský manuál
(28 stránky)
(28 stránky)
Měřící nástroje Altera Serial Digital Interface (SDI) MegaCore Function Uživatelský manuál
(140 stránky)
(140 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.026 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce