Altera RapidIO II MegaCore Function Uživatelský manuál Strana 149
- Strana / 218
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Chapter 6: Software Interface 6–11
Physical Layer Registers
August 2014 Altera Corporation RapidIO II MegaCore Function
User Guide
1.25_GB_ENABLE
[24] RW
Indicates whether port operation at 1.25 Gbaud is enabled in the
RapidIO implementation.
1’b0: The IP core cannot support 1.25 Gbaud operation.
1’b1: The IP core can support 1.25 Gbaud operation. This field can
only have this value if
1.25_GB_SUPPORT
has the value of 1
1'b1
2.5_GB_SUPPORT
[23] RO
Indicates whether the RapidIO II IP core supports port operation at
2.5 Gbaud.
1’b0: The IP core does not support 2.5 Gbaud operation.
1’b1: The IP core supports 2.5 Gbaud operation.
1'b1
2.5_GB_ENABLE
[22] RW
Indicates whether port operation at 2.5 Gbaud is enabled in the RapidIO
implementation.
1’b0: The IP core cannot support 2.5 Gbaud operation.
1’b1: The IP core can support 2.5 Gbaud operation. This field can
only have this value if
2.5_GB_SUPPORT
has the value of 1
1'b1
3.125_GB_SUPPORT
[21] RO
Indicates whether the RapidIO II IP core supports port operation at
3.125 Gbaud.
1’b0: The IP core does not support 3.125 Gbaud operation.
1’b1: The IP core supports 3.125 Gbaud operation.
1'b1
3.125_GB_ENABLE
[20] RW
Indicates whether port operation at 3.125 Gbaud is enabled in the
RapidIO implementation.
1’b0: The IP core cannot support 3.125 Gbaud operation.
1’b1: The IP core can support 3.125 Gbaud operation. This field can
only have this value if
3.125_GB_SUPPORT
has the value of 1
1'b1
5.0_GB_SUPPORT
[19] RO
Indicates whether the RapidIO II IP core supports port operation at
5.0 Gbaud.
1’b0: The IP core does not support 5.0 Gbaud operation.
1’b1: The IP core supports 5.0 Gbaud operation.
1'b1
5.0_GB_ENABLE
[18] RW
Indicates whether port operation at 5.0 Gbaud is enabled in the RapidIO
implementation.
1’b0: The IP core cannot support 5.0 Gbaud operation.
1’b1: The IP core can support 5.0 Gbaud operation. This field can
only have this value if
5.0_GB_SUPPORT
has the value of 1
1'b1
6.25_GB_SUPPORT
[17] RO
Indicates whether the RapidIO II IP core supports port operation at
6.25 Gbaud.
1’b0: The IP core does not support 6.25 Gbaud operation.
1’b1: The IP core supports 6.25 Gbaud operation.
1'b1
6.25_GB_ENABLE
[16] RW
Indicates whether port operation at 6.25 Gbaud is enabled in the
RapidIO implementation.
1’b0: The IP core cannot support 6.25 Gbaud operation.
1’b1: The IP core can support 6.25 Gbaud operation. This field can
only have this value if
6.25_GB_SUPPORT
has the value of 1.
1'b1
RSRV
[15:4] RO Reserved 12'b0
Table 6–13. Port 0 Control 2 CSR—Offset: 0x154
(1)
(Part 2 of 3)
Field Bits Access Function Default
- User Guide 1
- RapidIO II MegaCore Function 1
- Contents 3
- Contents v 5
- Chapter 5. Signals 6
- Chapter 6. Software Interface 6
- Chapter 7. Testbench 6
- 1. About The RapidIO II 9
- MegaCore Function 9
- Releases 10
- RapidIO II IP Core Features 10
- Features 11
- Device Family Support 12
- IP Core Verification 13
- Hardware Testing 14
- Interoperability Testing 14
- Note to Table 1–3: 16
- Notes to Table 1–4: 16
- Installation and Licensing 17
- 2. Getting Started 19
- Simulating IP Cores 22
- Transceiver Settings 26
- External Transceiver PLL 26
- 3. Parameter Settings 31
- Note to Table 3–1: 32
- Enable 16-Bit Device ID Width 33
- Logical Layer Settings 34
- Capability Registers Settings 35
- Device ID 36
- Vendor ID 36
- Revision ID 36
- Assembly ID 36
- Assembly Information CAR 37
- Enable Flow Control Support 38
- Enable Switch Support 38
- Number of Ports 38
- Port Number 39
- Maximum PDU 39
- Destination Operations CAR 40
- Port General Control CSR 40
- Port 0 Control CSR 41
- Lane n Status 0 CSR 41
- Extended Features Pointer CSR 41
- 4. Functional Description 43
- Note to Table 4–2: 44
- Clocking and Reset Structure 45
- Notes to Table 4–3: 46
- RapidIO II 47
- Transactions 55
- Notes to Table 4–6: 57
- Notes to Table 4–7: 59
- Note to Table 4–8: 59
- Note to Figure 4–9: 66
- Note to Table 4–10: 70
- Notes to Table 4–11: 71
- Table 6–60 on page 6–40 72
- Note to Table 4–12: 73
- Maintenance Module 74
- Maintenance Interface Signals 75
- Doorbell Module Block Diagram 86
- Preserving Transaction Order 87
- Doorbell Module Signals 88
- Generating a Doorbell Message 88
- Receiving a Doorbell Message 89
- Transaction ID Ranges 90
- Notes to Table 4–24: 92
- Note to Table 4–26: 94
- Note to Table 4–27: 95
- field 97
- User Receiving Write Request 100
- Logical Layer Interfaces 101
- Transport Layer 112
- Receiver 113
- Transmitter 114
- Physical Layer 115
- Physical Layer Interfaces 116
- Low-level Interface Receiver 116
- CRC Checking and Removal 117
- Protocol Violations 119
- Fatal Errors 119
- Maintenance Avalon-MM Slave 120
- Maintenance Avalon-MM Master 121
- Port-Write Reception Module 122
- Input/Output Avalon-MM Slave 122
- Input/Output Avalon-MM Master 123
- 5. Signals 125
- Physical Layer Signals 126
- Low Latency Signals 127
- Multicast Event Signals 128
- Chapter 5: Signals 5–5 129
- Note to Table 5–7: 130
- Chapter 5: Signals 5–7 131
- 5–8 Chapter 5: Signals 132
- Register-Related Signals 133
- Avalon-MM Interface Signals 133
- Note to Table 5–12: 134
- Chapter 5: Signals 5–11 135
- Note to Table 5–15: 136
- Error Reporting Signals 137
- 5–14 Chapter 5: Signals 138
- 6. Software Interface 139
- Memory Map 140
- Physical Layer Registers 144
- Note to Table 6–9: 147
- Note to Table 6–14: 154
- Note to Table 6–15: 158
- Note to Table 6–17: 160
- Note to Table 6–22: 164
- Note to Table 6–23: 164
- Note to Table 6–24: 165
- Note to Table 6–25: 165
- Note to Table 6–26: 166
- Note to Table 6–27: 167
- Notes to Table 6–28: 168
- Notes to Table 6–29: 169
- Note to Table 6–30: 169
- Note to Table 6–31: 169
- Notes to Table 6–32: 170
- Note to Table 6–34: 171
- Note to Table 6–35: 171
- Note to Table 6–36: 172
- Note to Table 6–37: 172
- Transmit Port-Write Registers 174
- Receive Port-Write Registers 175
- Note to Table 6–59: 178
- Error Management Registers 180
- Note to Table 6–66: 181
- Notes to Table 6–67: 183
- Notes to Table 6–70: 185
- Notes to Table 6–71: 185
- Doorbell Message Registers 191
- Note to Table 6–89: 193
- 7. Testbench 195
- 7–2 Chapter 7: Testbench 196
- Testbench Overview 196
- Testbench Sequence 197
- 7–4 Chapter 7: Testbench 198
- Chapter 7: Testbench 7–5 199
- SWRITE Transactions 200
- NREAD Transactions 200
- NWRITE_R Transactions 201
- NWRITE Transactions 202
- Doorbell Transactions 202
- Port-Write Transactions 203
- Testbench Completion 204
- Chapter 7: Testbench 7–11 205
- 7–12 Chapter 7: Testbench 206
- A. Initialization Sequence 207
- MegaCore Function v12.1 209
- Additional Information 213
- Info–2 Additional Information 214
- Document Revision History 214
- Additional Information Info–3 215
- Info–4 Additional Information 216
- Note to Table: 217
- Info–6 Additional Information 218
- Typographic Conventions 218
Související produkty a manuály pro Měřící nástroje Altera RapidIO II MegaCore Function
(198 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.556 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce