Altera Arria V Hard IP for PCI Express Uživatelský manuál Strana 187
- Strana / 288
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Chapter 9: Reset and Clocks 9–7
Clocks
December 2013 Altera Corporation Arria V Hard IP for PCI Express
User Guide
Transceiver Clock Signals
As Figure 9–5 indicates, there are two clock inputs to the PHY IP Core for PCI Express
IP core transceiver.
■
refclk
—You must provide this 100 MHz or 125 MHz reference clock to the Arria
V Hard IP for PCI Express IP core.
■
reconfig_clk
—You must provide this 100 MHz or 125 MHz reference clock to the
transceiver PLL. You can either use the same reference clock for both the
refclk
and
reconfig_clk
or provide separate input clocks. The PHY IP Core for PCI
Express IP core derives
fixedclk
used for receiver detect from
reconfig_clk
.
- User Guide 1
- Contents 3
- Chapter 7. IP Core Interfaces 5
- Chapter 9. Reset and Clocks 5
- Chapter 18. Debugging 8
- 1. Datasheet 9
- 1–2 Chapter 1: Datasheet 10
- Features 10
- Notes to Table 1–1: 11
- Release Information 12
- Device Family Support 12
- Configurations 12
- Debug Features 13
- IP Core Verification 14
- Recommended Speed Grades 15
- 1–8 Chapter 1: Datasheet 16
- Qsys Design Flow 25
- Generating the Testbench 26
- Modifying the Example Design 34
- Running Qsys 36
- Table 3–5 38
- On Chip r 40
- Simulating the Example Design 44
- Direct BFM’s shared memory 47
- {*reconfig_xcvr_clk*} 50
- Compiling the Design 51
- Programming a Device 51
- System Settings 54
- Port Functions 55
- Error Reporting 57
- 31 19 18 17 16 15 14 58
- Power Management 59
- Legacy Interrupt 63
- Base Address Registers 66
- PCI Express/PCI Capabilities 67
- Header 68
- 6. IP Core Architecture 75
- Avalon-ST Interface 77
- RX Datapath 77
- TX Datapath 77
- Altera FPGA 77
- Clocks and Reset 78
- Interrupts 79
- Transaction Layer 79
- Protocol Layers 80
- Configuration Space 81
- Data Link Layer 81
- Figure 6–4. Data Link Layer 82
- Physical Layer 83
- Figure 6–5. Physical Layer 84
- Multi-Function Support 86
- PCI Express Avalon-MM Bridge 86
- Avalon-MM Bridge TLPs 88
- Figure 6–9. Poor Address Map 93
- RX Block 97
- Avalon-MM RX Master Block 97
- TX Block 98
- Interrupt Handler Block 98
- 7. IP Core Interfaces 99
- Note to Table 7–1: 100
- RX Port 101
- Avalon-ST RX Interface 103
- Note to Figure 7–7: 108
- Avalon-ST TX Interface 113
- Note to Table 7–4: 116
- ECRC Forwarding 121
- Clock Signals 121
- Reset Signals 122
- and the LTSSM L0 state 124
- ECC Error Signals 125
- Interrupts for Endpoints 125
- Interrupts for Root Ports 126
- Completion Side Band Signals 126
- Specification, Rev. 2.1 128
- D E F 0 1 2 3 131
- Notes to Table 7–13: 132
- LMI Signals 136
- LMI Read Operation 137
- LMI Write Operation 137
- Power Management Signals 138
- (Full-Featured Qsys) 140
- Completer-Only Single DWord 141
- RX Avalon-MM Master Signals 143
- Transceiver Reconfiguration 145
- Serial Interface Signals 145
- PIPE Interface Signals 149
- Test Signals 153
- Notes to Table 7–27: 154
- 8. Register Descriptions 155
- Note to Table 8–2: 156
- Note to Table 8–3: 157
- Note to Table 8–4: 157
- Note to Table 8–5: 157
- Note to Table 8–6: 158
- Note to Table 8–7: 158
- Note to Table 8–8: 159
- PCI Express Mailbox Registers 167
- Note to Table 8–30: 168
- Root Port TLP Data Registers 170
- Sending a TLP 173
- Receiving a Completion TLP 173
- Endpoints 174
- Avalon-MM Mailbox Registers 175
- Spec 2.1 176
- 9. Reset and Clocks 181
- Example Design 182
- Hard IP for PCI Express 182
- 127 cycles 184
- ±300 PPM 185
- Note to Table 9–2: 186
- Transceiver Clock Signals 187
- Supported Message Types 189
- Notes to Table 10–1: 191
- Receive Buffer Reordering 192
- Notes to Table 10–2: 193
- MSI Interrupts 195
- 11–2 Chapter 11: Interrupts 196
- Note to Figure 11–4: 197
- Legacy Interrupts 198
- Application Layer 199
- 11–6 Chapter 11: Interrupts 200
- MSI/MSI-X Support 201
- Qsys System 202
- 12. Optional Features 203
- ECRC on the RX Path 204
- ECRC on the TX Path 205
- 13. Flow Control 207
- 13–2 Chapter 13: Flow Control 208
- Throughput of Posted Writes 208
- Chapter 13: Flow Control 13–3 209
- 13–4 Chapter 13: Flow Control 210
- 14. Error Handling 211
- Physical Layer Errors 212
- Data Link Layer Errors 212
- Transaction Layer Errors 213
- Note to Table 14–4: 215
- Figure 15–2 218
- Core User Guide 219
- 16. SDC Timing Constraints 221
- Endpoint Testbench 224
- Root Port Testbench 225
- Chaining DMA Design Examples 226
- Root Complex 227
- Chaining DMA 227
- Hard IP for 227
- PCI Express 227
- Note to Table 17–2: 232
- Note to Table 17–4: 233
- Test Driver Module 236
- DMA Write Cycles 237
- DMA Read Cycles 239
- Root Port Design Example 240
- Root Port 241
- Variation 241
- (variation_name.v) 241
- Root Port BFM 242
- BFM Memory Map 244
- Figure 17–6 248
- BFM Read and Write Procedures 250
- BFM Procedures and Functions 251
- BFM Configuration Procedures 256
- Shared Memory Constants 257
- 18. Debugging 271
- 18–2 Chapter 18: Debugging 272
- Link Training 272
- Chapter 18: Debugging 18–3 273
- 18–4 Chapter 18: Debugging 274
- Chapter 18: Debugging 18–5 275
- Setting Up Simulation 276
- Chapter 18: Debugging 18–7 277
- Use Third-Party PCIe Analyzer 278
- BIOS Enumeration Issues 278
- Notes to Table A–7: 280
- Chapter : A–3 281
- Notes to Table A–16: 282
- Additional Information 283
- Info–2 Revision History 284
- How to Contact Altera 285
- Typographic Conventions 286
Související produkty a manuály pro Měřící nástroje Altera Arria V Hard IP for PCI Express
(286 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.141 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce