Altera 10-Gbps Ethernet MAC MegaCore Function Uživatelský manuál Strana 99
- Strana / 175
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Chapter 8: Registers 8–5
MAC Registers
February 2014 Altera Corporation 10-Gbps Ethernet MAC MegaCore Function User Guide
0x140
rx_preamble_inserter_control
RW 0x0
■ Bit 0 enables the preamble passthrough
mode on the receive datapath.
0—Disables the preamble passthrough
mode.
1—Enables the preamble passthrough
mode.
■ Bits 1 to 31 are reserved.
For more information on the XGMII
decapsulation in the preamble passthrough
mode, refer to “XGMII Decapsulation” on
page 7–11.
0x141 –
0x7FF
Reserved — — Reserved for future use.
RX Frame Decoder (0x800:0xBFF)
0x800
rx_frame_control
RW 0x3
Specifies valid frame types, pause frames
handling, and use of supplementary
addresses.
Refer to “Rx_frame_control Register” on
page 8–16 for the bit description.
0x801
rx_frame_maxlength
RW 1518
■ Bits 0 to 15 specify the maximum allowable
frame length. The MAC asserts the
avalon_st_rx_error[3]
signal when the
length of the receive frame exceeds the
value of this register.
■ Bits 16 to 31 are reserved.
0x802
rx_frame_addr0
RW 0x0 6-byte primary MAC address. You must map
the address to the registers in the following
manner:
■
rx_frame_addr0
= Last four bytes of the
address
■
rx_frame_addr1[
0:15]= First two bytes of
the address.
Bits 16 to 31 are reserved.
Example:
If the primary MAC address is 00-1C-23-17-
4A-CB, set
rx_frame_addr0
to 0x23174ACB
and
rx_frame_addr1
to 0x0000001C.
The IP core uses the primary MAC address to
filter unicast frames when the
en_allucast
bit of the
rx_frame_control
register is set
to 0.
0x803
rx_frame_addr1
(1) RW 0x0
Table 8–2. MAC Registers (Part 4 of 15)
Word
Offset
Register Name Access
Reset
Value
Description
- User Guide 1
- Contents 3
- Contents iv 4
- Chapter 8. Registers 5
- Chapter 9. Interface Signals 5
- 1. About This IP Core 7
- 1.2. Release Information 8
- 1.3. Device Family Support 9
- 1.4. IP Core Verification 10
- ■ Timestamping is enabled 12
- ■ ptp_1step is disabled 12
- 2.2. Design Flows 14
- 2.3.2. Simulate the IP Core 15
- 2.4.1. Specify Parameters 16
- 2.4.3. Simulate the System 17
- [1] register bit to 1 18
- 3. 10GbE MAC Design Examples 19
- 3.2.0.2. Base Addresses 22
- Table 3–5 on page 3–10 23
- Creating a New 10GbE Design 24
- 3.6. 10GbE Testbenches 26
- 3.6.3. 10GbE Testbench Files 27
- 10GbE Testbenches 28
- Notes to Table 3–6: 36
- 4.1. Software Requirements 39
- Altera FPGA 40
- Design Example 40
- 4.2.1. Base Addresses 41
- Figure 4–3. Testbench 43
- The <ip 44
- Simulator 45
- 5.2.2. Base Addresses 49
- 1G/10GbE Design Example Files 50
- 5.5. 1G/10GbE Testbench 51
- Testbench 52
- 1G/10GbE Testbench 53
- 5.5.4.2. Backplane-KR Mode 55
- 6.2.1. Base Addresses 62
- ModelSim Simulator 66
- 7. Functional Description 68
- Architecture 69
- 7.2. Interfaces 70
- 7.2.2. SDR XGMII 71
- 7.2.3. GMII 71
- 7.2.4. MII 71
- 7.3. Frame Types 72
- 7.4. Transmit Datapath 72
- 7.4.2. Address Insertion 73
- Note to Figure 7–5: 74
- 7.4.4. XGMII Encapsulation 75
- 7.4.6. SDR XGMII Transmission 76
- Figure 7–7. Endian Conversion 77
- 7.5. Receive Datapath 78
- 7.5.4. Address Checking 79
- 7.5.5. Frame Type Checking 79
- 7.5.6. Length Checking 80
- 7.5.7. CRC-32 and Pad Removal 81
- 7.5.8. Overflow Handling 82
- Congestion and Flow Control 83
- 7.7.2.1. PFC Frame Reception 86
- Figure 7–11. Fault Signaling 87
- 7.9. IEEE 1588v2 88
- IEEE 1588v2 89
- 7.9.1. Architecture 90
- 7.9.2. Transmit Datapath 91
- 7.9.3. Receive Datapath 92
- 7.9.4. Frame Format 92
- MAC Header 93
- Note to Figure 7–16: 94
- 8. Registers 95
- 8.1. MAC Registers 96
- 0x0C1. Bits 4 to 31 are 98
- 0x0C3. Bits 4 to 31 are 98
- Register Name Access 100
- Bits 4 to 31 are reserved 101
- register 111
- Name R/W Description 112
- 8.3. Register Initialization 113
- 8–20 Chapter 8: Registers 114
- Register Initialization 114
- Chapter 8: Registers 8–21 115
- 8–22 Chapter 8: Registers 116
- Chapter 8: Registers 8–23 117
- 8–24 Chapter 8: Registers 118
- Chapter 8: Registers 8–25 119
- 9. Interface Signals 120
- Note to Table 9–1: 121
- Note to Figure 9–2: 123
- Note to Figure 9–3: 123
- Notes to Figure 9–4: 124
- Note to Figure 9–5: 125
- 9.0.3. SDR XGMII 127
- Note to Figure 9–7: 128
- Note to Figure 9–8: 129
- 9.0.4. GMII Signals 130
- 9.0.5. MII Signals 130
- Note to Table 9–8: 136
- Note to Table 9–9: 139
- 1588v2 feature 142
- 10. Design Considerations 150
- 10GbE MAC XAUI/10G BASE-R PHY 151
- Reconfiguration Controller 151
- A. Frame Format 153
- Figure A–2. VLAN Frame Format 154
- A.3. Pause Frame 155
- Figure A–5. PFC Frame Format 156
- B. Time-of-Day (ToD) Clock 157
- B.4. Parameter Setting 158
- ■ Bits 20 to 31: Not used 160
- B.6.1. Adjusting ToD’s Drift 161
- C. Packet Classifier 162
- Classifier 163
- D. ToD Synchronizer 166
- D.2. Block Diagram 167
- D.4. ToD Synchronizer Signals 169
- Additional Information 171
- Info–2 Additional Information 172
- Document Revision History 172
- Additional Information Info–3 173
- How to Contact Altera 174
- Typographic Conventions 174
- Additional Information Info–5 175
Související produkty a manuály pro Měřící nástroje Altera 10-Gbps Ethernet MAC MegaCore Function
Měřící nástroje Altera OCT Uživatelský manuál
(10 stránky)
(10 stránky)
Měřící nástroje Altera Embedded Systems Development Kit, Cyclone III Edit Uživatelský manuál
(82 stránky)
(82 stránky)
Měřící nástroje Altera 40-Gbps Ethernet MAC and PHY MegaCore Function Uživatelský manuál
(199 stránky)
(199 stránky)
Měřící nástroje Altera PHYLite Uživatelský manuál
(61 stránky)
(61 stránky)
Měřící nástroje Altera Arria GX Uživatelský manuál
(32 stránky)
(32 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.029 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce